Измерительные приборы ведущих мировых производителей
Свяжитесь с нами:
(4812) 35-81-67
(4812) 35-81-68

Блок управления 904.28, 904.29

904.28, 904.29

Доставка: В любой регион

Доставка продукции осуществляется транспортными компаниями на Ваш выбор. Подробнее

Мы рекомендуем:

ЖелДорЭкспедиция
ЖелДорЭкспедиция
Деловые линии
Деловые линии

Application

Measuring instruments with WIKA inductive contact devices may be used in operation rooms subject to explosion hazards in danger areas of Zone 1 and Zone 2. Provided they are supplied from a suitable and certified control circuit (e.g. WIKA control device of type 904.15).

Besides the Ex areas WIKA inductive contact devices are primarily used where it is crucial to obtain especially safe contact with high switching frequency. Since the contacts function in liquid filling, they can be used even under very specific operating conditions. Some typical application fields are chemistry, petrochemistry and nuclear facilities.

Special Features

  • 904.28 for 1 inductive contact, output: 1 x SPDT
  • 904.29 for 2 inductive contacts, output: 2 x SPDT
  • 903.30 for 1 inductive contact, safety equipment (SN or S1N), output:1 x Sicherheitasgerichteter relay output; 1 x Fortschaltausgang; 1 x passive electronic output
  • type of protection: EEx-ia IIc
  • electrical ratings: 250Vac/2A/500VA (1A for typ 904.30)
  • on delay and drop out delay: 20ms
  • ambient temperature: -20.. +60°C 
  • ingress protection IP 20
  • control units with 20.. 30Vdc power supply
    • type 904.31 - 1 relais output
    • type 904.32 - 2 relais output
    • type 904.33 - 1 sicherheitsgerichter relais output

Description

The WIKA inductive contact device is a contact-free device. Basically, it consists of an initiator, located on the nominal value pointer, including its fully potted electronics and mechanical construction with a movable control vane.

The control vane is moved by the instrument pointer (nominal value pointer). The initiator is supplied with DC voltage. If the control vane moves into the clearance of the initiator, its internal resistance increases (= activated state / the initiator has high-resistance). The change in the current rating arising from this is the input signal for the switching amplifier of the control device.

Рекомендуем:
Блок управления для электроконтактов
Блок управления для электроконтактов 905.12, 905.13
Applications Amplification of switching current Increasing the lifetime Special Features 905.12 for 1 contact, output: 1 x SPDT 905.13 for 2 contacts, output: 2 x SPDT 905.14 for 2 contacts, output: 1 x SPDT intermittent, e.g. for pump co
Электроконтакты
Электроконтакты 821, 830, 830-E
Тип 821, контакты с магнитным поджатием Тип 831, индуктивные контакты Тип 830 E, электронные контакты Применение Контроль и регулирование промышленных процессов Контроль установок и переключения электрических цепей Индикация предельных значений Индуктивные контакты для безопасного срабатывания при примене
Резиновый кожух для манометров
Резиновый кожух для манометров 910.18
Применение Защита от ударных воздействий, коррозии и атмосферных влияний Для манометров с выдуваемой задней стенкой Специальные особенности Увеличивает срок службы манометров Для радиальных и осевых манометров Легкая установка Описание Кожух должен быть установлен непосредственно н
Скоба для монтажа на поверхность
Скоба для монтажа на поверхность 910.16
Applications For mounting pressure gauge and other indicating instruments Special Features For versions to DIN 16 281 the instrument mounting bracket is designed as a two-piece clamp. With the split clamp of the other versions, instruments with fixed lines connected, e.g. diaphragm seals
^